- Currently Unavailable
Full Bed Length Bumpers 200 x 96 cm (High-Sided)
- 96cm High-Sided for Mattress Overlays - the 96cm height accommodates the additional mattress-to-rail distance created when a pressure relief overlay or replacement mattress is placed on the profiling bed base; the additional 20cm of height over the standard 76cm version (NCL-CSBPB) fills the gap that a standard bumper would leave above the mattress surface level when an overlay is in use.
- Overlay-Compatible Rail Protection - the high-sided height is specifically indicated for profiling beds with mattress overlays or raised rail configurations where the standard 76cm bumper height does not reach the top of the bed rail above the overlay; a gap between the bumper top edge and the rail top in an overlay configuration creates an impact and entrapment risk at the exposed rail section above the bumper.
- Wipe-Clean for NHS IPC - wipe-clean cover allows NHS IPC decontamination between patient uses; full 200cm length provides complete inner rail coverage; padded construction reduces impact injury risk at the rail surface across the full 96cm height; suitable for care home and hospital profiling beds where pressure relief overlays are in routine clinical use.
- CSBPB Range Selection - the bed rail risk assessment should confirm which height is appropriate: standard 200x76cm (NCL-CSBPB) for beds without overlays; high-sided 200x96cm (NCL-CSBPBH) for beds with overlays or raised rails; 200x105cm (NCL-CSBPBX) for three wooden side rail configurations; specifying the incorrect height leaves part of the rail unprotected.
Full Bed Length Bumper - 200x96cm - High-Sided - Mattress Overlay Compatible
The Full Bed Length Bumper (200x96cm, High-Sided) provides padded inner rail coverage at 96cm height for profiling beds with mattress overlays or raised rail configurations where the standard 76cm height (NCL-CSBPB) would leave the rail exposed above the overlay surface. Wipe-clean cover for NHS IPC decontamination; full 200cm length for complete rail coverage. The 200x105cm version for three wooden side rails is NCL-CSBPBX.
Specifications
| Specification | Detail |
|---|---|
| Reference | NCL-CSBPBH |
| Dimensions | 200 x 96 cm (79" x 38") |
| Cover | Wipe-clean |
| Indicated For | Profiling beds with mattress overlays or raised rails |
| Standard Height Version | NCL-CSBPB (200 x 76 cm) |
| Three-Rail Version | NCL-CSBPBX (200 x 105 cm) |
Regulatory Compliance
MHRA guidance on bed rail safety requires that bumpers cover the full accessible rail height without leaving exposed sections; the use of a pressure relief overlay raises the mattress surface relative to the bed rail, increasing the height of exposed rail above the mattress. A 76cm standard bumper on a bed with a 15-20cm overlay may leave 15-20cm of exposed rail above the bumper top edge, creating an impact and entrapment risk at that exposed section. The 96cm high-sided version eliminates this gap. CQC Regulation 12 (safe care) documentation should confirm the bumper height is appropriate for the specific bed and overlay combination in use, with the height selection rationale recorded in the bed rail risk assessment. Mental Capacity Act 2005 obligations apply where relevant.
Frequently Asked Questions
How does a mattress overlay affect the required bumper height?
A pressure relief overlay placed on the profiling bed base raises the effective mattress surface by the thickness of the overlay, typically 10-20cm. The bed rail remains fixed at its original height, so the mattress-to-rail-top distance decreases while the bumper fitted below the mattress level must now reach a higher point relative to the resident's body position on the raised mattress. A 76cm standard bumper that fitted flush with the top of a non-overlay rail will leave an exposed rail section equal to the overlay thickness when an overlay is added. The 96cm high-sided bumper is specified to accommodate this increased height requirement. The bed rail risk assessment should confirm the overlay thickness and the required bumper height before procurement.
Can the high-sided bumper be used on beds without a mattress overlay?
Yes, but the clinical team should confirm that the 96cm height is appropriate for the bed configuration. On a profiling bed without an overlay, the 96cm bumper would extend above the bed rail if the rail height is less than 96cm, which could create excess material that does not lie flat against the rail. The standard 76cm version (NCL-CSBPB) is the appropriate specification for beds without overlays or raised rails where the rail height is consistent with the standard 76cm coverage. The high-sided version should not routinely replace the standard version in settings without overlays or raised rails, as correct fit and secure positioning depend on the bumper height matching the rail height.
NCL-CSBPBH
- 96cm High-Sided for Mattress Overlays - the 96cm height accommodates the additional mattress-to-rail distance created when a pressure relief overlay or replacement mattress is placed on the profiling bed base; the additional 20cm of height over the standard 76cm version (NCL-CSBPB) fills the gap that a standard bumper would leave above the mattress surface level when an overlay is in use.
- Overlay-Compatible Rail Protection - the high-sided height is specifically indicated for profiling beds with mattress overlays or raised rail configurations where the standard 76cm bumper height does not reach the top of the bed rail above the overlay; a gap between the bumper top edge and the rail top in an overlay configuration creates an impact and entrapment risk at the exposed rail section above the bumper.
- Wipe-Clean for NHS IPC - wipe-clean cover allows NHS IPC decontamination between patient uses; full 200cm length provides complete inner rail coverage; padded construction reduces impact injury risk at the rail surface across the full 96cm height; suitable for care home and hospital profiling beds where pressure relief overlays are in routine clinical use.
- CSBPB Range Selection - the bed rail risk assessment should confirm which height is appropriate: standard 200x76cm (NCL-CSBPB) for beds without overlays; high-sided 200x96cm (NCL-CSBPBH) for beds with overlays or raised rails; 200x105cm (NCL-CSBPBX) for three wooden side rail configurations; specifying the incorrect height leaves part of the rail unprotected.